Discover the world with our lifehacks

How do I setup my Yamaha RX V473?

How do I setup my Yamaha RX V473?

RX-V473 Advanced Setup Menu

  1. Set the unit to Standby Mode using the Power button.
  2. While holding down Straight button, hit the Power button.
  3. Use the Program Selector buttons to navigate the Advanced setup menu items and the Straight button to make selections.

How do I balance my Yamaha receiver speakers?

If you would like to change the level between the mains, you can use the [BALANCE CONTROL] either located on the front panel of the receiver or in the Set-Menu. A common challenge people have is that they try to adjust the main speakers to match the center or rear levels.

How do I increase the bass on my Yamaha receiver?

You can also adjust the tone with the front panel controls. Press TONE CONTROL to select “Treble” or “Bass”, then press PROGRAM to make an adjustment.

What are the best dB levels for surround sound?

As a general rule speakers should be set between 70-80 dB in volume. This can be established using a decibel meter. Several variables impact this, including the position of the speakers, the distance between them, and the acoustics of the room.

Why is my Yamaha receiver so quiet?

americanaudiophile : Check the level of the speakers in the AVR speaker set up menu. If they are all set below 0db then turn up them up so the highest is at zero and the others have been turned up that same amount. Don’t be afraid to go higher than -20 on the receiver main volume control.

What does extra bass do on Yamaha receiver?

The idea behind “Extra Bass” is fairly straightforward: if you happen to have main speakers capable of delivering respectable amounts of low end output without buckling, you can run them full range AND send a copy of their bass content to your subwoofer, effectively increasing bass output.

What hits harder 2ohm or 4ohm?

In terms of which subwoofer hits harder, drawing from the explanation as given above, the 2-ohm subwoofer produces a louder sound than the 4-ohm subwoofer. So in that sense, technically speaking, the 2-ohm subwoofer hits harder than a 4-ohm subwoofer.

Can you use 4 ohm speakers 8 ohm receiver?

Four-ohm speakers are another story, they can place higher demands on 6- or 8-ohm rated receivers and amps’ power reserves, but even those receivers/amps won’t run into trouble with 4-ohm speakers, as long as you’re not playing music or movies at a very loud volume.

What dB is best for bass?

The paper states that “the range of preferred bass levels among individual listeners is 17dB, from -3dB (listener 346) to 14.1dB (listener 400).” This finding astounded me, not only because of the range of difference of 17dB — a lot — but that someone out there preferred -3dB of bass cut.

What dB to set subwoofer to?

Using the internal test tones, calibrate each speaker to roughly the same level (use 75dB as a reference). It’s ok to boost the sub level a couple of dB if you want a bit more bass impact. So if you set all of your speakers to 75dB, don’t sweat setting your sub to say 77-78dB.

What is subwoofer trim on the Yamaha rx-v473?

One of the more unique audio features that the Yamaha RX-V473 offers is Subwoofer Trim, which is a control that prevents the lower frequencies to overlap with the higher frequencies outputted by the front speakers. This results to better bass quality and a more stabilized front stage.

Does the Yamaha rx-v473 have an HDMI port?

The Yamaha RX-V473 is not the kind of AV receiver to get if you want to easily connect a portable device to an HDMI port. But if you only have a small home theater setup, the 4 HDMI inputs and single HDMI output found on the back might be sufficient. Below is the back panel layout. Click on image to enlarge for a clearer view.

What is the output power of the rx-v473?

RX-V473 Discontinued RX-V473 Amplifier Section Channel 5.1 Amplifier Section Rated Output Power (1kHz, 1ch driven) 115W (6ohms, 0.9% THD) Amplifier Section Rated Output Power (20Hz-20kHz, 2ch driv 80W (6ohms, 0.09% THD)

Does the Yamaha rx-v473 have THX certification?

The RX-V473 doesn’t have any THX certification, but that’s not worth factoring into a buying decision, since the Yamaha has solid sound quality. Yamaha has its own automatic speaker calibration technology, dubbed the Yamaha Parametric Room Acoustic Optimizer (YPAO).