How do I fix star SP700 error?
Star SP700 Status Light Issues
- Power off the printer.
- Push the lever to open the printer’s back cover.
- If the printer is out of paper, load a new roll and close the cover on the paper.
- If there is a paper jam, clear the jam and close the cover.
- Power the printer back on.
How do I reset my SP700 printer?
Use a pen to press and hold the Red button on the back of the printer.
- Both red and green lights will blink simultaneously for 5 seconds:
- Keep holding down the button.
- Keep holding down the button.
- When both lights begin blinking simultaneously again, release the button for 1 second:
- Immediately press it again.
How do I connect to SP700?
Printer Hardware Setup
- Connect the power cable to the printer and plug the other end into a power outlet.
- Connect an ethernet cable to the printer port labeled ‘100/10 BASE’.
- Plug the other end of the ethernet cable into an open numbered port on the router.
- Open the printer’s front lid to reveal the ink ribbon tray.
How do I factory reset my star printer?
Unplug the Ethernet cable from the back of the printer….Hold the Feed button until the Ready and Error lights start to blink blue and red.
- Release the Feed button.
- Close the paper hatch.
- The ready light should be blue.
- Turn the printer off and back on.
- The printer is now reset and in DHCP mode.
How do I reset my tsp650ii?
With the printer turned off, find the reset button located on the back of the printer, and then use a pen to press and hold down the button. While holding down the reset button, turn on the printer. Continue holding the reset button for 10 seconds after turning on the printer, and then release the reset button.
How do I reset my printer ink pad?
Steps to reset Waste Ink Pad Counter on Epson Printers
- Extract the archived files using WinRar.
- Open the .exe file in order to run the utility and select the Epson printer type.
- After selecting the printer model, click OK.
- In the Maintenance section, select Waste ink pad counter and press OK.
How do I reset my Epson kitchen printer?
FACTORY RESET
- Turn off the printer.
- Press and hold the reset button on the back of the printer (normally located to the right of the ethernet port).
- Turn on the printer while holding the reset button.
- Wait until a message prints indicating that the printer is resetting.
How do I find my IP address SP700?
If it is an older TSP100II or SP700 wait until you hear the printer unit make a noise and then release the Feed button. The printer will produce two slips of paper. The second slip will will show the printer’s current IP address.
How do I find the IP address of my star SP700 printer?
Finding the printer’s IP address
- Turn off the Star printer.
- Press and hold the feed button.
- Turn the printer back on.
- Continue to hold the feed button until the Network Configuration report prints out.
- Confirm the printer IP address. An example IP address would be: 192.168.1.73.
What do the status lights on the star sp700 mean?
This section covers issues communicated by the status lights on the front of the Star SP700 ticket printer. The ERROR light is blinking and the POWER light is solid. An ERROR light blinking about once per second means the printer has either run out of paper or is about to run out.
How do I check the IP parameters of my Star sp700 printer?
Instructions for Star SP700: Flip the power switch to turn off the printer. Hold down the FEED button and power the printer back on. Release the FEED button after the printer beeps. Two sheets of paper will print. At the bottom of the second, look for ‘Current IP Parameters Status’.
How do I Reset my Star sp700 to factory settings?
Instructions for Star SP700: Flip the power switch to turn off the printer. Hold down the FEED button and power the printer back on. Release the FEED button after the printer beeps.
Why is there no error light on my printer in shopkeep?
This problem can occur when you skip a step during the printer’s initial setup. If there are no error messages in ShopKeep and no error lights lit on the printer, continue below to troubleshoot. Follow the steps hereto check if the printer is listed on the ‘Printers’ screen in the ShopKeep app. Click to Enlarge