How do I reset my HP ProCurve 1800 switch to factory settings?
How do I reset factory defaults on the ProCurve 1800 Series Switches?
- Remove the power cord from the back of the switch.
- Connect port 1 to port 2 on the front panel, using a standard network cable.
- Reconnect the power cord to the rear of the switch.
- Wait at least 40 seconds before disconnecting port 1 from port 2.
How do I factory reset my HP ProCurve 2626?
Factory Reset When enabled, the switch can be reset to factory defaults by depressing the “Clear” and “Reset” buttons together, releasing the “Reset” button while holding the “Clear” button down, and releasing the “Clear” button as soon as the “Test” light begins to flash rapidly.
How do you reset a ProCurve switch?
To initialize, or reboot, a ProCurve Switch, perform the following steps:
- Press the small, recessed Reset button on the face of the switch.
- Issue the command, reload from within the CLI.
- Or, issue the command, boot system flash to reboot into either primary or secondary flash.
How do I reset my HP ProCurve 2510 24?
How to reset a ProCurve 2510-24g to default settings
- Press in both the Clear and Reset buttons (tiny buttons on the left edge)
- Release the Reset button after the port lights come on (~2 seconds)
- When the Self-Test LED starts flashing (to the left of the Clear and Reset buttons), release the Clear button.
How do I reset my HP 1820 switch?
To execute the factory default reset on the switch, perform these steps:
- Using a small, thin tool with blunt ends (such as a paper clip), press the Reset button on the front of the switch.
- Continue to press the Reset button until the Fault LED light begins to flash.
- Release the Reset button.
How do I factory reset my HP ProCurve?
To execute the factory default reset on the switch, perform these steps:
- Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
- Continue to press the Clear button while releasing the Reset button.
- When the Self Test LED begins to blink, release the Clear button.
How do I restore my hp to factory settings?
Turn on the laptop and immediately press the F11 key repeatedly until System Recovery starts. On the Choose an option screen, click “Troubleshoot.” Click “Reset this PC.” Click either “Keep my files” or “Remove everything” depending on which you prefer.
How do I turn off HP ProCurve Switch?
Thank you for contacting HP Networking Support. The only way to completely shut down the switch is by pulling the power plug. This is by design. Since the switch can only be powered off through physical intervention, it negates the risk of someone inadvertently issuing a command to shut it down remotely.
How do I reload my HP Router?
How to: Using the reload command with HP ProCurve Switches
- Step 1: Write the old config to memory.
- Step 2: Issue the reload command.
- Step 3: Be paranoid about it (Optional)
- Step 4: Do whatever you came to do.
- Step 5: Canceling the reload.
- Step 6: Write the changes to memory.
How do you reset a ProCurve 2510?
How do I Reset my ProCurve switch to factory settings?
■CLI ■Clear/Reset button combination ProCurve recommends that you save your configuration to a TFTP server before resetting the switch to its factory-defaultconfiguration. You can also save your configuration via Xmodem, to a directly connected PC.
How do I clear the configuration on my HP ProCurve?
The command is quite simple, just run erase startup-config, it’ll tell you what you’re about to do, and finally acknowledge what you’re about to do with an y. This command should work on just about any firmware level of any HP Procurve or Aruba Switch. The current configuration will be deleted and the device rebooted.
How do I get help with the ProCurve web browser interface?
If you need information on specific features in the ProCurve Web Browser Interface (hereafter referred to as the “web browser interface”), use the online Help. You can access the Help by clicking on the Help text on top right side of any of the web browser interface screens. Figure 1-4. Help for Web Browser Interface
What is ProCurve Manager Plus?
• Investment Protection: The modular software architecture of ProCurve Manager Plus will allow ProCurve to offer network administra tors add-on software solutions that complement their needs.