What is totally not so stubby area in OSPF?

That means an autonomous system border router (ASBR) resides in our stubby area. What we expect to happen in a totally not-so-stubby-area is that we WILL NOT be getting all the summary LSAs, just a default route. However we will also redistribute networks with type 7 LSAs into OSPF.

Table of Contents

What is totally NSSA area?

Totally Stubby NSSA This area type can only accept intra-area, external and the default route (which is generated by default). Totally Stubby NSSA areas allow only LSAs Type-1, 2, [3] and 7. The default route in a Stub area is generated by default and is injected in the area as Type-3 LSA.

What is totally NSSA in OSPF?

Not So Stubby Area (NSSA) Normally, NSSA are do not accept Type 5 LSAs. But it convert Type 5 to Type 7 and then accept. After NSSA, at the ABR, this convert process is done again and Type 7 LSAs is converted to Type 5 LSAs. OSPF NSSA with Accepted LSAs.

What types of LSAs are present in a not so stubby area?

Not-so-stubby Areas An NSSA makes use of type 7 LSAs, which are essentially type 5 LSAs in disguise.

What is totally not so stubby area?

A stub area is an area in which advertisements of external routes are not allowed, reducing the size of the database. A totally stubby area (TSA) is a stub area in which summary link-state advertisement (type 3 LSAs) are not sent.

What are the OSPF States?

Following are the OSPF States we’ll be examining:

Down state.
Attempt state.
Init state.
2-Way state.
Exstart state.
Exchange state.
Loading state.
Full state.

What are the OSPF area types?

There are five types of OSPF areas: Backbone area (area 0), Standard area, Stub area, Totally stubby area, and No so stubby area (NSSA).

What is the difference between stub area and NSSA?

In that case, you might make it totally stubby, that is, give it only a default route. An NSSA is a bit like a stub as far as the internal OSPF topology is concerned, but it is allowed to connect to the outside world. In other words, it is allowed to have an ASBR border router.

What is the difference between a stubby area and a totally stubby area?

What is stubby area in OSPF?

Stub area, also called stub area, the so-called stub area, means that the area does not accept any external routes of non-OSPF network, if it wants to reach those external routes, only Need to send it through the default route. This area supports 1, 2, and 3 LSAs.

What are the 7 stages of OSPF?

OSPF routers go through the seven states, called Down, Attempt/Init, Two ways, Exstart, Exchange, Loading and full while building adjacency with other OSPF speaking routers.

What is OSPF stubby area?

What is totally stubby area in OSPF?

We are back with OSPF areas discussion and this time we will tackle about the Totally Stubby Area. You have to pronounce it right though if you know what I mean. Totally Stubby Area is a Cisco proprietary feature which works like a Stub Area but a stricter area type.

What is a totally not so stubby area?

Totally not so stubby areas are areas where we expect a stub network, however we want to do some redistribution. That means an autonomous system border router (ASBR) resides in our stubby area. What we expect to happen in a totally not-so-stubby-area is that we WILL NOT be getting all the summary LSAs, just a default route.

How to configure totally stubby area with LSA?

If Stub Area do not allow certain LSA Types like Type 4 and Type 5 LSAs, Totally Stubby area do not allow it as well plus no Type 3 LSA too. The result is even smaller routing table. To configure Totally Stubby area, we have to add the “ no-summary ” command after the “ stub ” command.

Is our area 20 a stub area or a totally stubby area?

Aedes still showing as a stub area but the Totally Stubby area can be identified on Anopheles. It is showing that it is also a Stub area but there are no-summary LSA which confirms that our area 20 is a Totally Stubby area.